Easy Guide To Make Wire Wrapped Rings With Beads

With the right gauge wrapped wire and excellent beads, you can make excellent wire wrapped rings with beads perfectly. However, you will need the right kind of skills to do exactly that. Actually, you can make a good ring from a wrapped loop.

Unlike an ordinary wire, a wrapper is secure and provides a creator with an opportunity to attach a clasp too. You can also make connectors which you’ll use to attach the beads and add attractive dangles.

What’s Next When You Have The Right Wire?

According to The Spruce, the wire you need to use must be large enough. Such a diameter will allow you to implant a thin cable through. A good gauge should be between 22 and 26.

A thin wire is not strong and may not withstand a simple loop. For this reason, a wrapped loop will do it for you.

Materials Needed For A Wire Wrapped Loop

All you need is a wire to make the wrap and the beads to decorate the ring. You may find it extremely difficult to making a wrapped loop with a wire gauge more than 25g. In this tutorial, we are going to demonstrate how you can make a loop using a soft sterling wire weighing 22g.

You’ll need three types of pliers. The round, chain or bent nose pliers. You also need a flush cutter to cut the line into the right sizes.

wire wrapped rings

We advise that the wire you intend to use must be long enough to allow the wrapping of the beads around it. Each of the wrapped loops requires about a 1/2 inch of the wire. From the end of the cable, measure 1/2 inch and bend the wire 90 degrees using a round nose pliers.

Make The Loop

Use your finger to push the shorter end of the wire around the pliers until it wraps well. Take the wire off from the upper jaws of the pliers to the lower one. Finish up the wrap by completing the circle. Ensure each end of the wires perfectly meets each other.

Remove the formed loop from the jaws of the pliers. Adjust the loop for a smoother and finer finish. Once done, the loop should be round. The extreme end of the loop and the main wire should be 90 degrees to each other.

Fine Tuning The Loop

Carefully grasp the loop with pliers from the top. Don’t press the jaws of the pliers too hard. Take extra caution to avoid damaging or leaving scratch marks on the loop. Using another plier, wrap the tail of the wire around the parent cable.

You can use your fingers in case you don’t have a plier. Make sure you wrap the wire tightly into a coil and the closer to the base of the ring. To secure the wire well, make at least more than one wrap around the wire.

Fusin Beads recommends 1-1/2 turns. However, the number of turns will vary with the strength of the wire and your desire. Once you secure the wire, close the coil by tucking the end of the wire into the next ring.

Decorate The Ring With Beads

Add a bead on the loop and repeat the same procedure on the rest of the beads. As you do so, you’ll be creating a beaded link. Above each bead, remember to make 90 degrees bend on the cable. Ensure you have enough space to make a ring wrap. The coil should resemble the one on the opposite side of the bead.

Connect the adjacent loops, make sure all their components are in place. Ensure you do this before closing the loop. Close the loop by wrapping the tail below the ring. Coil the wire upwards facing the beads. Note that the size of all the coils must be same.

When you insert the beads, be artistic. You can vary the sizes of beads or use different colors to bring out a contrast. You can mix bright and dark colored beads for a striking feature. You can also come up with different type and sizes of the ring.

Adding Final Touches To Your Coil

You have added the beads to the ring, what next? You now have to give your ring that striking look. Trim unnecessary wire to the ring and polish any rough surfaces using sandpaper. However, polish the wire with caution to avoid abrasive its surface.

Rub the finished ring against the skin or cloth just to make sure it is not scratching the skin or getting caught in the fabric. Make sure the rings sit comfortably on the gauge. All the loops must also be in their correct sizes. You need to get this right as any defect will affect the appearance of the ring.

We understand that it’s your first time you are making the wire wrapped rings. Chances are that you may not get all shapes similar. However, you can take advantage of various ring making tutorials available online.

For instance, Maggie outlines 45 amazing ways how you can make your choice. You can perfect your ring with these simple tips. These tips are specifically for those who want do-it-yourself kind of a ring.

Conclusion

The wrapped ring project outline above is a simple project that you can do for yourself at home. You don’t need any specialized skills or materials to create a fascinating homemade ring that will amaze the people.

You only need to be artistic. The materials we have specified are available at your local.

However, the cost you’ll pay will vary with the type of wire and beads you choose. A heavy gauge cable will cost more compared to lighter ones. Synthetic beads cost less but don’t appeal as much as the natural ones.

The choice of the material is up to your decision. All you need to ensure is that the ring you create is unique.